Stamina Info Protocol

About 561 wordsAbout 2 min

This page documents the Stamina Info task, which reads the stamina shown on the home screen at the end of the daily task chain and reports the estimated time until it refills naturally. The task is defined in tasks/stamina_info.json, enters at StaminaInfo, is checked by default, and runs last in the task chain.

Task entry and options

Task	Entry	Options
Stamina Info	`StaminaInfo`	None (fixed ROIs, runs by default)

Flow

StaminaInfo (routed by CheckStaminaPage: on home?)
  ├─ yes → StaminaInfo.Read (retried via ReadRetry, 3 attempts max) → output refill info (still failing → task fails)
  └─ no  → StaminaInfo.ClickHome (retried via ClickHomeRetry, 3 attempts max) → re-confirm (3 consecutive misses → task fails)

Conventions:

The StaminaInfo entry uses the custom recognition CheckStaminaPage (agent/custom/recognition/stamina.py) as a router: it confirms the main interface with template main_option.png; on the home screen it routes to StaminaInfo.Read, otherwise it routes to StaminaInfo.ClickHome, which taps the home button and re-confirms that the read starts from the home screen.
Routing is done via context.override_next (same pattern as CheckEventHub) instead of listing Read and ClickHome together in one next list: with a plain list, a Read recognition failure would fall through to ClickHome, which also matches on the home screen and clicks it — an infinite "read fails → tap home → read again" loop.
StaminaInfo.Read uses the custom recognition ReadStamina (agent/custom/recognition/stamina.py); on failure (e.g. incomplete stamina digits) it is retried at most twice (3 read attempts in total) and then the task ends as failed instead of looping. The attempt count is controlled by the StaminaInfo.ReadRetry gate node (max_hit=2 with timeout=0, one recognition per screenshot round), so it is independent of device OCR speed and never spins for a long time.
The StaminaInfo.ClickHome branch is bounded symmetrically by the StaminaInfo.ClickHomeRetry gate (max_hit=2 with timeout=0): the home button is matched/clicked at most 3 times; after other_max (default 3) consecutive misses (clicks that never reach home) CheckStaminaPage gives up (recognition fails). Both StaminaInfo and StaminaInfo.ClickHome set timeout=0, so once the give-up decision is made the task fails immediately without an extra wait window.

ReadStamina recognition

The home-screen stamina digits are rendered at a -45° tilt. ReadStamina rotates each ROI by the opposite of tilt_angle to straighten the digits before OCR, then extracts the first integer:

Param	Default	Description
`current_roi`	`[1120, 512, 38, 44]`	ROI of the current stamina digits
`cap_roi`	`[1152, 484, 28, 30]`	ROI of the stamina cap digits
`tilt_angle`	`-45`	Screen tilt of the digits (legacy alias: `rotate_angle`)
`stamina_cap`	none	Optional fallback cap value if OCR of `cap_roi` fails

Missing ROIs, non-positive ROI width/height, or an ROI beyond the screenshot bounds produce a warning and skip OCR without aborting the task.
stamina_cap is coerced to int and validated; invalid values are warned and ignored.

Refill-time calculation

Recovery rate: 4 min / 1 point (STAMINA_RECOVER_MINUTES_PER_POINT).
Below cap: missing = cap - current, full_time = now + missing * 4min, following MAA-style output:
```
Stamina will be full at <YYYY-MM-DD HH:MM>. (Xh Ym remaining)
```
At the natural-recovery cap, stamina no longer grows: reports "already at the natural recovery cap, no longer refilling over time"; if above cap (e.g. after a stamina item), reports "above the natural recovery cap, no longer refilling over time".
Any read/write failure only skips this output; other tasks are unaffected.